Breville

Breville AirRounder Plus Connect LPH708

Answers and step-by-step fixes from the official Breville manual.

What does the display or light show?

• REPLACE FILTER icon lit: The filter needs to be replaced. The REPLACE FILTER icon on the display means the filter has reached the end of its life.
• Wi-Fi symbol flashing fast: Ready to connect to Wi-Fi. The unit is in pairing mode and waiting for the app to connect.
• Wi-Fi symbol flashing slowly: In a different pairing mode. You touched and held the power button to switch the unit into another connection mode.
• Wi-Fi symbol steady on: Connected to Wi-Fi. The connection to your home network was successful.
• Wi-Fi symbol off after setup: Connection was not made. The unit could not join your Wi-Fi network.
• Child lock icon lit: Child lock is on. The control panel buttons are locked and will not respond.
• Light ring blue: In cooling mode. A blue light ring shows the unit is running as a cooling fan.
• Light ring red: In heating mode. A red light ring shows the unit is running as a heater.
• Ambient temperature flashing: Target temperature reached. The room has reached your set temperature so heating has paused and oscillation has stopped.
• Display shows 'OFF': Cooling down after heating. After heating is switched off, the display shows OFF while the unit cools down.
• Air quality light: Blue: Air quality is very good. Blue on the air quality pattern means the lowest particle reading.
• Air quality light: Bright Purple: Air quality is good. Bright purple on the air quality pattern means a good reading.
• Air quality light: Orange: Air quality is fair. Orange on the air quality pattern means a fair reading.
• Air quality light: Red: Air quality is poor. Red on the air quality pattern means a poor reading, over 100 AQI.

Common problems

The unit will not start

1. Is the power plug connected and the outlet switched on? Check that the power plug is connected to a power outlet and the outlet is turned on.
2. Is the purifier fan heater assembled correctly? Check that the purifier fan heater is assembled correctly.
3. Is the filter fitted correctly? Check that the filter is fitted correctly in place. The unit will not operate if the filter is missing or wrong.

Not enough air coming out

1. Did you remove the filter packaging? Make sure the filter is removed from the packaging.
2. Are the filters clean? Check that the filters are clean.
3. Is the air inlet or outlet blocked? Check for any obstructions in the air inlet and/or outlet.

The unit is making too much noise

1. Is the filter clogged? Check if the filter is clogged and ready for replacement.
2. Is the rear housing cover closed properly? Check that the rear housing cover is closed properly.
3. Is the unit on a level surface? Check that the unit is on a level surface.

The purifier will not connect to Wi-Fi

1. Is the purifier within range of the router? Check that your purifier is within range of the Wi-Fi router.
2. Are you on a 2.4GHz network during setup? During the setup process you must be on a secure 2.4GHz Wi-Fi network.
3. Is the Wi-Fi password correct? Make sure the Wi-Fi password you entered is correct.
4. Have you tried a power cycle? Unplug the purifier for 10 seconds and plug it back in.

Step-by-step guides

Replace the filter

1. Remove the rear housing cover
2. Pull out the used filter using its pull tabs
3. Unpack the new filter and fit it with the pull tabs facing the opening
4. Check the filter is fitted correctly
5. Put the rear housing cover back on
6. Press and hold the filter reset button for 10 seconds

Clean the filter and air quality sensor

1. Switch off and unplug the unit
2. Let all parts cool down before cleaning
3. Wipe the outside with a clean, dry cloth
4. Vacuum the openings on the air quality sensor cover with a small hand brush
5. Vacuum the pre-filter with a brush or upholstery attachment

Connect the purifier to Wi-Fi

1. Connect your phone to your home Wi-Fi network
2. Leave the purifier on standby or turn it on
3. Wait for the Wi-Fi symbol to flash fast on the display
4. In the app, tap Add Device or the icon in the top right
5. Follow the prompts in the app